February 25th, 2010
- Compatible with Dodge Cummins Turbodiesel 6.7L (2007 – )*
- With CaTCHER softwares inside
- With three different performance levels to choose from: 40 / 70 / 100 HP
- Provides better fuel economy and optimized driveability
- Download up to three times faster than the competition, with a typical ECM update taking under five minutes
- Adjust your tire height using ABS programming in just seconds from 22,5” to 44” in 1/10” increments
- Manual High Idle enabled in all performance levels
- Read your Diagnostic Trouble Codes or DTCs in plain text interpretation and clear them
- Requires no tools or fuses to pull
- Quick and easy access to free upgrades from the MADS website using the built-in USB connector
- Get free internet updates from MADS
- Has the most complete keyboard in the industry
- Quick and hassle-free installation
- Very reliable because it uses your OEM hardware
- Program and fine tune your vital engine parameters
- Power on Demand
Your Smarty JR Programmer is equipped with Power on Demand, which allows you to select your preferred power level from 0 to 99 using the arrow keys. For security purposes, the changes apply only after the throttle is released.
Your Smarty JR Programmer will allow you to choose from 3 different software levels based on horsepower improvements. Software 1 through Software 3 use a modified Torque Management or TQM. You will experience improved throttle response, but your tranny and the rest of your driveline will be set to a safe limit for your tranny and the rest of your driveline.
The figures specified below are based on Mads Electronics’ in-house Dyno tests made on stock trucks. Mads checked the horsepower at the rear wheels of the stock trucks with Smarty J67 Programmer tested twice a day and rounded it down to get those figures.
- Software 1: 40 Horsepower increase
- Software 2: 70 Horsepower increase
- Software 3: 100 Horsepower increase
*Incompatible to trucks produced after March 4, 2009
Posted in Articles, Features | No Comments »
February 18th, 2010
Compatible with Dodge RAM 5.8 L 1998-2002- With 10 different CaTCHER softwares to choose from
- Read your Diagnostic Trouble Codes or DTCs in plain text interpretation and erase them
- Adjust your tire height using ABS programming (from 22,5” to 44”) in 1/10” increments just seconds
- Manual High Idle enabled in all performance levels
- Requires no tools or fuses to pull
- Quick and easy access to free upgrades from the MADS website using the built-in USB connector
- The Electronic Control Module or ECM is capable of automatic recovery after interruptions
- Spend just 1 1/2 minutes to update your ECM
- Programmable Speed Limiter from 25 to 250 MPH (trucks 2000 and older only have a speed adjustment and not programmable in MPH)
- Untraceable
Software Levels
- Software 0: Half power (reduced power, no smoke)
- Software 1: Fuel saver (average 2 MPG gains, aggressive timing, heavy towing not recommended)
- Software 2: Only more fuel and Boost fooling*
- Software 3: More fuel and Boost fooling with added timing
- Software 4: Soft CaTCHER with no added timing*
- Software 5: Soft CaTCHER with added timing
- Software 6: Mild CaTCHER with no added timing*
- Software 7: Mild CaTCHER with added timing
- Software 8: CaTCHER with no added timing* ˚˚
- Software 9: CaTCHER with added timing˚˚
*Use Software 2, 4, 6 and 8 to stack with other aftermarket power-adding devices that already produce added timing. Do not use Software 1, 3, 5, 7 and 9 if other installed devices already produce added timing to your vehicle.
˚˚May be difficult to handle on slippery roads because of the aggressive throttle response. Do not use Software 8 and 9 for prolonged periods. You run the risk of having dangerously high Exhaust Gas Temperatures or EGTs and damaging the Diesel Particulate Filter or DPF when you reach over 105 MPH.
Posted in Articles, Features | No Comments »
February 18th, 2010
Compatible with Dodge RAM 5.9 L 2003-2007- With 3 different CaTCHER softwares to choose from
- Provides better fuel economy
- Experience improved drivability
- Read your Diagnostic Trouble Codes or DTCs in plain text interpretation and erase them
- Adjust your tire height using ABS programming (from 22,5” to 44”) in 1/10” increments just seconds
- Manual High Idle enabled in all performance levels
- Requires no tools or fuses to pull
- Convenient keyboard
- Completely reliable because it works off of the OEM hardware
- Quick and easy access to free upgrades from the MADS website using the built-in USB connector
- Spend just 3 ½ to 5 minutes to update your Electronic Control Module or ECM
- Untraceable
- Quick and hassle-free installation
- Power on Demand
Your Smarty JR Programmer is equipped with Power on Demand, which allows you to select your preferred power level from 0 to 99 using the arrow keys. For security purposes, the changes apply only after the throttle is released.
Your Smarty JR Programmer will allow you to choose from 3 different software levels based on horsepower improvements. Software 1 through Software 3 use a modified Torque Management or TQM. You will experience improved throttle response, but your tranny and the rest of your driveline will be set to a safe limit for your tranny and the rest of your driveline.
The figures specified below are based on Mads Electronics’ in-house Dyno tests made on stock trucks. Mads checked the horsepower at the rear wheels of the stock trucks with Smarty JR Programmer tested twice a day and rounded it down to get those figures.
- Software 1: 40 Horsepower increase
- Software 2: 70 Horsepower increase
- Software 3: 100 Horsepower increase
Posted in Articles, Features | No Comments »
February 18th, 2010
Compatible with Dodge RAM 5.9 L 2003-2007- With 10 different CaTCHER softwares to choose from
- Read your Diagnostic Trouble Codes or DTCs in plain text interpretation and erase them
- Adjust your tire height using ABS programming (from 22,5” to 44”) in 1/10” increments just seconds
- Manual High Idle enabled in all performance levels
- Requires no tools or fuses to pull
- Convenient keyboard
- Completely reliable because it works off of the OEM hardware
- Quick and easy access to free upgrades from the MADS website using the built-in USB connector
- Spend just 3 ½ to 5 minutes to update your Electronic Control Module or ECM
- Untraceable
- Power on Demand*
*Only for Smarty S06 PoD, Power on Demand allows you to select your preferred power level from 0 to 99 using your Smarty keyboard. For security purposes, the changes apply only after the throttle is released.
Your Smarty Programmer S06 will allow you to choose from 10 different software levels based on horsepower improvements. Software 1 through Software 9 use a modified Torque Management or TQM. You will experience improved throttle response, but your tranny and the rest of your driveline will be set to a save limit.
The figures specified below are based on Mads Electronics’ in-house Mustang Dyno tests made on stock trucks. Mads checked the horsepower at the rear wheels of the stock trucks tested twice a day and rounded it down to get those figures.
- Software 0: Half power
- Software 1: 30 Horsepower increase with added timing
- Software 2: 60 Horsepower increase with no added timing**
- Software 3: 60 Horsepower increase with added timing
- Software 4: 90 Horsepower increase with no added timing**
- Software 5: 90 Horsepower increase with added timing
- Software 6: 130 Horsepower increase with no added timing**
- Software 7: 130 Horsepower increase with added timing
- Software 8: 170 Horsepower increase with no added timing** ˚˚
- Software 9: 170 Horsepower increase with added timing˚˚
**Use Software 2, 4, 6 and 8 to stack with other aftermarket power-adding devices that already produce added timing. Do not use Software 1, 3, 5, 7 and 9 if other installed devices already produce added timing to your vehicle.
˚˚Do not use Software 8 and 9 for prolonged periods. You run the risk of having dangerously high Exhaust Gas Temperatures or EGTs and damaging the Diesel Particulate Filter or DPF when you reach over 105 MPH.
Posted in Articles, Features | No Comments »
February 18th, 2010
Compatible with Dodge RAM 6.7 L (2007 – )*- With 10 different CaTCHER softwares to choose from
- Read your Diagnostic Trouble Codes or DTCs in plain text interpretation and erase them
- Adjust your tire height using ABS programming (from 22,5” to 44”) in 1/10” increments just seconds
- Manual High Idle enabled in all performance levels
- Requires no tools or fuses to pull
- Convenient keyboard
- Completely reliable because it works off of the OEM hardware
- Programmable Speed Limiter from 25 to 250 MPH
- Access and control engine parameters for fine tuning
- Quick and easy access to free upgrades from the MADS website using the built-in USB connector
- The Electronic Control Module or ECM is capable of automatic recovery after interruptions
- Spend just 5 ½ minutes to update your ECM (The fastest in the industry!)
*For 2009 trucks and 2007 and newer vehicles that use the new bootloader software, please check the production date on the ECM before installing the CaTCHER software. The Smarty S67 has not been tested on 2009 trucks using the ECM bootloader software produced after March 4, 2009. Refer to the 18-007-09 service bulletin for more information.
Your Smarty Programmer S67 will allow you to choose from 10 different performance or software levels based on horsepower improvements. Software 1 through Software 9 use a modified Torque Management or TQM. You will experience improved throttle response, but your tranny and the rest of your driveline will be set to a safe limit for your tranny and the rest of your driveline.
The figures specified below are based on Mads Electronics’ in-house Dyno Dinamics Twin Retarder Dyno tests made on stock trucks. Mads checked the horsepower at the rear wheels of the stock trucks tested twice a day and rounded it down to get those figures.
- Software 0: Half power
- Software 1: 30 Horsepower increase with added timing
- Software 2: 60 Horsepower increase with no added timing**
- Software 3: 60 Horsepower increase with added timing
- Software 4: 90 Horsepower increase with no added timing**
- Software 5: 90 Horsepower increase with added timing
- Software 6: 130 Horsepower increase with no added timing**
- Software 7: 130 Horsepower increase with added timing
- Software 8: 170 Horsepower increase with no added timing** ˚˚
- Software 9: 170 Horsepower increase with added timing˚˚
**Use Software 2, 4, 6 and 8 to stack with other aftermarket power-adding devices that already produce added timing. Do not use Software 1, 3, 5, 7 and 9 if other installed devices already produce added timing to your vehicle.
˚˚Do not use Software 8 and 9 for prolonged periods. You run the risk of having dangerously high Exhaust Gas Temperatures or EGTs and damaging the Diesel Particulate Filter or DPF when you reach over 105 MPH.
Posted in Articles, Features | No Comments »
February 18th, 2010
The Smarty Programmer is a handheld tuner that allows the user to do modifications on a vehicle’s fuel injection settings to achieve increased power and torque and enhanced drivability without tampering with its safety and emissions systems.
The Smarty Programmer works exactly like replacement EPROMs or “chips” inside the on-board control module, except you don’t need to pop the hood and pull out the control module. You can simply hook up the handheld to your under-dash or ALDL port, take a few minutes to install it and you can achieve the same drive-train improvements.
Mads Electronics is the company responsible for bringing this innovative product as a result of 40 years of experience in electronics and software. Mads developed the CaTCHER software which stands for Clutch and Traction Challenger, which is their main tuning software and allows improvements in throttle response, spools up the turbo 200 RPM sooner (on average), increases the efficiency of the injection timing, alters the torque management and reduces fuel consumption up to 15%.
These Mads Smarty Programmer models are available for these specific vehicles:
- Smarty Programmer S06/S06 PoD – Dodge RAM 5.9 L 2003-2007
- Smarty JR Programmer PoD – Dodge RAM 5.9 L 2003-2007
- Smarty Programmer S03 – Dodge RAM 5.8 L 1998-2002
- Smarty Programmer S67 – Dodge RAM 6.7 L 2007-2009*
*For 2009 trucks and 2007 and newer vehicles that use the new bootloader software, please check the production date on the ECM before installing the CaTCHER software. The Smarty S67 has not been tested on 2009 trucks using the ECM bootloader software produced after March 4, 2009. Refer to the 18-007-09 service bulletin for more information.
Posted in Articles | No Comments »
February 18th, 2010
Thank you for dropping by on our website! We made this website to provide information about MADS Electronics’ Smarty Programmers to interested readers. We would like you to know that we are not connected with the manufacturer in any way. We are simply here to let you know about their great products and how your Dodge RAM can benefit from getting one, from an interested party to another. So, let’s get on with it then. Have fun browsing our site and we hope you find what you’re looking for!
Posted in Articles, Features | 1 Comment »
